Manual for Bose N123 Remote Control

The Bose N123 Remote Control is a universal infrared remote designed for Bose audio/video systems, featuring programmable buttons, backlit keypad, learning capability for other devices, macro functions, and compatibility with various Bose products. Below are key sections for overview, features, setup, programming, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Infrared transmitter, LCD display, programmable buttons, backlight, learning sensor, battery compartment.

Package Contents

Unpack and verify all items are present.

1. Bose N123 Remote Control unit.
2. 2 x AAA alkaline batteries.
3. Quick Start Guide.
4. Compatibility code list.

WARNING! Keep batteries away from children. Do not mix old and new batteries.

Initial Setup

Prepare remote for first use.

1. Insert batteries: Open battery compartment, insert AAA batteries with correct polarity.
2. Power on: Remote activates automatically; check LCD for power indicator.
3. Test basic functions: Point at Bose device, press POWER to ensure communication.
4. Select device mode: Press TV, DVD, or AUDIO button to control corresponding device.

CAUTION! Handle remote with care; avoid dropping or exposing to liquids.

Specifications

• Model: Bose N123 Remote Control.
• Power Source: 2 x AAA batteries (1.5V each).
• Battery Life: Approximately 12 months with typical use.
• Transmission: Infrared (IR) at 38kHz frequency.
• Operating Range: Up to 30 feet (9 meters).
• Dimensions: 6.5 x 2.2 x 0.8 inches (165 x 56 x 20 mm).
• Weight: 4.2 oz (120 g) with batteries.
• Compatibility: Bose audio/video systems; programmable for other brands.
• Warranty: 1-year limited warranty.

Controls and Functions

Front Panel: POWER, Numeric keypad, Volume, Channel, Navigation arrows, MUTE, MENU, BACK, EXIT.

Mode Buttons: TV, DVD, AUDIO, CABLE, AUX for device selection.

Special Functions: SETUP (enter programming mode), LEARN (for learning commands), MACRO (record sequence), BACKLIGHT (toggle illumination). Display: Shows active mode and battery status.

Programming the Remote

Program remote for Bose or other devices.

1. Enter setup: Press and hold SETUP until LED blinks twice.
2. Select device: Press corresponding mode button (e.g., TV).
3. Enter code: Use numeric keypad to enter 3-digit code from compatibility list.
4. Test: Point at device, press POWER to verify control.
5. Learning mode: Press LEARN, point original remote at sensor, press button to learn.

Tip: Keep original remote close during learning; avoid bright light interference.

Advanced Functions

Macro programming for multi-step commands.

1. Record macro: Press and hold MACRO, press sequence of buttons, release MACRO.
2. Assign macro: Press desired button (e.g., PLAY) to store macro.
3. Execute: Press assigned button to run macro sequence.
4. Clear macro: Hold MACRO and SETUP for 5 seconds to reset.
5. Backlight: Press BACKLIGHT to illuminate keypad for 10 seconds.

WARNING! Do not point remote at direct sunlight during learning; may cause errors.

Battery Replacement

Replace batteries when display dims or remote becomes unresponsive.

1. Open battery compartment on rear.
2. Remove old batteries; dispose properly.
3. Insert new AAA batteries with correct polarity (+/-).
4. Close compartment; remote resets automatically.

CAUTION! Use only AAA alkaline batteries; do not recharge non-rechargeable batteries.

Care & Cleaning

Remove batteries before cleaning. Wipe with dry, soft cloth; avoid chemicals.

CAUTION! Do not submerge in water; keep away from heat sources.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. Copyright © 2025 Bose Corporation; all rights reserved. For support, visit www.bose.com/support or contact 1-800-999-2673.

Troubleshooting

Reset: Remove batteries, press all buttons for 10 seconds, reinsert batteries.

Service: 1-800-999-2673; www.bose.com/support