Bose Wave Remote Control Manual

The Bose Wave Remote Control is designed to operate compatible Bose Wave music systems, providing convenient wireless control over audio playback, source selection, volume, preset stations, alarm functions, and system settings. Below are key sections for overview, features, setup, operation, functions, maintenance, and troubleshooting.

1. Features at a Glance 2. Package Contents 3. Initial Setup 4. Specifications 5. Control Layout & Functions 6. Basic Operation 7. Advanced Functions 8. Battery Replacement 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Infrared (IR) remote control unit with ergonomic design, dedicated buttons for primary system functions, and long-range operation.

Feature	Description
Power	Turns the Bose Wave system On/Standby
Source Select	Cycles between CD, AUX, AM/FM Tuner
Volume Up/Down	Adjusts audio output level
Preset Stations (1-6)	Direct access to saved radio presets
Play/Pause	Controls CD playback
Skip/Track Forward/Back	Navigates CD tracks
Alarm Set/Adjust	Configures alarm time and settings
Display Dimmer	Adjusts brightness of system display
Mute	Instantly silences audio
Clock Set	Enters clock setting mode

Package Contents

Unpack and verify all items are present.

Bose Wave Remote Control (1 unit)
CR2032 3V Lithium Coin Cell Battery (pre-installed)
Quick Start Guide
Safety and Warranty Information

NOTE: If any item is missing or damaged, contact Bose customer support.

Initial Setup

Ensure remote is ready for use.

Remove the battery insulation tab: Pull the plastic strip from the battery compartment.
Point the remote: Aim the front (IR emitter) towards the Bose Wave system's IR sensor.
Check operation: Press POWER. The system should respond within a clear line of sight (up to 20 feet/6 meters).
If unresponsive: Ensure no obstructions, replace battery if necessary, and retry.

CAUTION! Do not mix old and new batteries. Dispose of used batteries properly.

Specifications

Model: Bose Wave Remote Control (compatible with Wave Music System III, Wave Radio, etc.)
Power Source: One CR2032 3V Lithium Coin Cell
Battery Life: Approximately 1 year with normal use
Operating Range: Up to 20 feet (6 meters), requires direct line of sight
Communication: Infrared (IR)
Dimensions: Compact, ergonomic design for handheld use
Weight: Lightweight (with battery)
Operating Temperature: Standard indoor conditions

Control Layout & Functions

Top Row: POWER, MUTE, DISPLAY (Dimmer). Middle: SOURCE, Numeric Presets (1-6), VOLUME Up/Down. Bottom: PLAY/PAUSE, SKIP Forward/Back, ALARM, CLOCK SET.

Detailed Functions: POWER toggles system On/Standby. SOURCE cycles input. PRESETS recall saved radio stations. VOLUME adjusts level. PLAY/PAUSE controls CD. SKIP changes tracks. ALARM accesses alarm menu. CLOCK SET enters time setting mode. DISPLAY cycles through brightness levels.

Basic Operation

Turning On: Press POWER. Volume: Use VOLUME +/-. Muting: Press MUTE; press again or adjust volume to unmute. Source Selection: Press SOURCE repeatedly until desired input (CD, AUX, TUNER) is selected.

For Radio: Tune manually via system buttons or use PRESETS (1-6).
For CD: Insert disc, press PLAY/PAUSE.
For Auxiliary: Connect external device to AUX input, select AUX source.

Tip: Keep remote pointed at the system's front panel during use.

Advanced Functions

Setting the Clock: Press and hold CLOCK SET until display flashes. Use HOUR and MINUTE (often via VOLUME or dedicated buttons on main unit) to set time. Press CLOCK SET again to confirm.

Setting Alarms: Press ALARM to enter alarm menu. Use remote or system buttons to set alarm time, source (Radio/CD/Buzzer), and volume. Save settings.

Programming Radio Presets: Tune to desired station on main unit. Press and hold a PRESET button (1-6) for 3 seconds until confirmation.

Display Dimmer: Press DISPLAY to cycle through High, Low, and Off (display off) brightness settings.

Battery Replacement

Replace battery when remote becomes unresponsive or range decreases significantly.

Slide open the battery compartment cover on the back of the remote.
Remove the old CR2032 battery, noting the orientation (+ side up).
Insert a new CR2032 3V Lithium battery with the positive (+) side facing up.
Slide the cover back into place until it clicks.
Test remote operation.

WARNING! Use only CR2032. Do not recharge, disassemble, or heat the battery. Keep away from children.

Care & Maintenance

Clean remote with a soft, dry cloth. Do not use liquids, abrasive cleaners, or compressed air.

CAUTION! Avoid extreme temperatures, humidity, and direct sunlight. Do not drop or subject to strong impacts.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. Contains transmitter module FCC ID: [To be filled by manufacturer]. Copyright © Bose Corporation. Bose and Wave are registered trademarks of Bose Corporation. For support, visit www.bose.com/support or contact Bose Customer Service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote does not work	Dead battery, obstruction, out of range	Replace battery; ensure clear line of sight within 20 ft; point directly at IR sensor.
Intermittent operation	Weak battery, low angle, interference	Replace battery; hold remote level; avoid strong ambient IR light (sunlight, halogens).
Button press not recognized	Dirty contacts, button stuck	Clean remote surface; ensure no debris under buttons.
System does not turn on via remote	Remote not programmed, system in protect mode	Check compatibility; use main unit POWER button to wake system first.
Presets not responding	Presets not saved, system memory reset	Reprogram presets; check if system power was interrupted.

Reset: Remove battery for 60 seconds, then reinsert to reset remote.

Service: For persistent issues, contact Bose Customer Support: 1-800-999-2673 or www.bose.com.