The Bose UFS-20 Floor Stands are universal speaker stands designed to securely mount compatible Bose speakers at optimal listening height. Constructed with durable materials, they feature adjustable height settings, integrated cable management, a stable weighted base, and universal mounting plates to accommodate various Bose speaker models. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.
Key components: Adjustable height columns, Universal mounting plate, Weighted base with floor spikes/glides, Cable management channels, Assembly hardware kit.
| Feature | Description |
|---|---|
| Adjustable Height | Column extends from 36" to 48" for optimal speaker placement |
| Universal Mounting Plate | Compatible with various Bose speaker models (check compatibility list) |
| Weighted Base | Provides stability; includes removable floor spikes for carpet and rubber glides for hard floors |
| Cable Management | Internal channels hide speaker wires for clean appearance |
| Assembly Hardware | Includes all necessary screws, wrenches, and mounting brackets |
| Construction | Steel and high-density polymer for durability |
| Finish | Black matte powder-coated finish |
| Load Capacity | Supports up to 30 lbs per stand |
| Base Dimensions | 12" x 12" square for enhanced stability |
| Warranty | Limited 5-year warranty (see documentation) |
Unpack and inspect all components. Ensure you have a clean, level floor surface.
WARNING! Stands are heavy; use two people for assembly to avoid injury. Ensure all bolts are securely tightened.
Position stands correctly for optimal audio performance.
CAUTION! Do not exceed 30 lbs weight limit. Ensure speaker is securely fastened before releasing.
Height Adjustment: Loosen collar, extend column, retighten collar. Floor Spikes: Screw in/out to level stand on uneven floors. Mounting Plate: Adjustable orientation for proper speaker angle.
Tools Required: Included hex wrenches, spirit level (not included).
Fine-tuning: Adjust speaker angle by loosening mounting plate bolts, tilting speaker 0-15 degrees, retightening. Cable Management: Remove side cover to access channel, route wire, replace cover. Stability Check: Periodically verify all connections are tight.
Compatible with Bose 300, 500, 700 series and other models with compatible mounting patterns.
Tip: Have assistant hold speaker during mounting to prevent dropping.
Integrated channel hides speaker wires for clean installation.
WARNING! Do not pinch wires when replacing cover. Ensure wires are not sharply bent.
Weighted base and proper installation prevent tipping. Always use on level surface. Keep away from high-traffic areas where stands might be bumped. Use included safety strap (if provided) to secure speaker to stand in earthquake-prone areas.
Use dry, soft cloth for cleaning. For stubborn marks, dampen cloth with water only. Do not use abrasive cleaners or chemicals.
CAUTION! Do not use wax, polish, or silicone-based products. Avoid excessive moisture.
FCC Part 15: Class B digital device; complies with interference limits. Copyright © 2023 Bose Corporation; all rights reserved. Bose and UFS-20 are trademarks of Bose Corporation. For support, visit www.bose.com/support or contact 1-800-999-2673.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Stand wobbles | Uneven floor or loose components | Adjust floor spikes for leveling; tighten all bolts and collars. |
| Speaker not secure | Incorrect screws or loose mounting | Use correct length screws; tighten mounting bolts securely. |
| Height adjustment stuck | Collars overtightened or debris | Loosen collar completely; clean column; re-adjust gently. |
| Cable won't fit channel | Wire too thick or connector too large | Use 16-gauge or smaller wire; remove connectors before routing. |
| Finish scratched | Abrasive cleaning or impact | Clean with soft cloth only; avoid contact with sharp objects. |
Re-tightening: Check all bolts and collars every 6 months for security.
Service: 1-800-999-2673; www.bose.com/support