bose cinemate manual remote

The Bose CineMate manual remote is designed to control the Bose CineMate series home theater speaker systems. It provides intuitive access to essential functions such as power, volume control, input selection, and audio mode adjustments. Below are key sections covering features, setup, operation, programming, and troubleshooting for the remote control.

1. Features at a Glance 2. Installation & Setup 3. Remote Control Layout 4. Basic Operations 5. Advanced Functions 6. Programming the Remote 7. Battery Replacement 8. Care & Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Ergonomic design, backlit buttons (on select models), infrared (IR) transmitter, dedicated system control buttons.

Feature	Description
Power Button	Turns the CineMate system on/standby
Volume Controls	Adjusts master volume up/down
Mute Button	Instantly mutes/unmutes audio
Input Select	Cycles through connected audio sources (TV, AUX, etc.)
Audio Mode	Selects sound profiles (Dialogue, Movie, Music)
Bass Control	Adjusts low-frequency output level
Setup Button	Accesses system configuration menu
Backlight (if equipped)	Illuminates buttons in low-light conditions
IR Learning Capability	Can be programmed to control other devices
Battery Compartment	Holds two AAA batteries

Installation & Setup

Unpack remote and inspect for damage. Ensure CineMate system is properly connected and powered.

Insert batteries: Open compartment, install two AAA batteries observing polarity.
Pair with system: Point remote at CineMate control console, press POWER to test communication.
Verify operation: Test volume, mute, and input selection functions.
Program additional devices (optional): Use setup procedure to control TV or other components.

WARNING! Use only recommended battery types. Do not mix old and new batteries.

Remote Control Layout

Top section: POWER button. Center: Volume rocker, MUTE, Input Select. Lower section: Audio Mode, Bass Control, Setup. Rear: Battery compartment cover.

Button Functions: POWER (system on/standby), VOL +/- (adjust volume), MUTE (toggle sound), INPUT (cycle sources), AUDIO MODE (select sound profile), BASS +/- (adjust bass), SETUP (enter programming mode).

Basic Operations

Power On/Off: Press POWER to toggle system power.
Volume Adjustment: Use VOL+ to increase, VOL- to decrease volume.
Mute: Press MUTE to silence audio; press again to restore.
Input Selection: Press INPUT repeatedly to cycle through available sources.
Audio Mode Selection: Press AUDIO MODE to switch between Dialogue (enhances speech), Movie (wide dynamic range), Music (balanced frequency response).
Bass Adjustment: Press BASS+ or BASS- to increase/decrease low-frequency output.

Tip: For best performance, point remote directly at CineMate control console from within 20 feet.

Advanced Functions

Setup Menu Access: Press and hold SETUP for 3 seconds until indicator light flashes.

Factory Reset: In setup menu, navigate to RESET option to restore default settings.
IR Code Learning: Program remote to control other devices (TV, Blu-ray player) by learning their IR codes.
Backlight Control (if equipped): Adjust backlight timeout or disable in settings.
Volume Limit: Set maximum volume level to prevent excessive loudness.

Note: Advanced functions may vary by CineMate model. Refer to specific system manual for details.

Programming the Remote

To control other devices (e.g., TV):

Enter learning mode: Press and hold SETUP until light flashes twice.
Press device button (e.g., TV POWER) you wish to program.
Point original remote at CineMate remote (front, 1-3 inches apart).
Press and hold button on original remote until CineMate remote light flashes.
Test programmed button by pointing at target device.

CAUTION! Ensure both remotes have fresh batteries. Perform programming in normal room lighting.

Battery Replacement

Replace batteries when remote response becomes weak or intermittent.

Slide open battery compartment cover on rear.
Remove old batteries, observing polarity orientation.
Insert two new AAA batteries (alkaline recommended).
Close cover securely.
Test remote functions.

WARNING! Dispose of old batteries properly. Do not recharge non-rechargeable batteries.

Care & Maintenance

Keep remote clean and dry. Use soft, dry cloth for cleaning; avoid liquids or abrasive cleaners.

CAUTION! Do not expose to extreme temperatures, humidity, or direct sunlight for prolonged periods.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. This device complies with Part 15 of the FCC Rules. Copyright © Bose Corporation. For support, visit www.bose.com/support or contact Bose Customer Service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Remote not working	Dead batteries, obstruction	Replace batteries; ensure clear line of sight to console.
Intermittent response	Weak batteries, distance	Replace batteries; move within 20 feet of console.
Buttons unresponsive	Battery corrosion, damage	Clean battery contacts; inspect for physical damage.
Cannot program other devices	IR learning failure	Ensure original remote is IR (not RF); repeat programming steps carefully.
Backlight not working (if equipped)	Settings, battery	Check backlight setting in menu; ensure batteries are fresh.

Reset: Remove batteries for 30 seconds, then reinstall to reset remote.

Service: Contact Bose Customer Support or visit www.bose.com for assistance.