Bose Acoustamas 10 Manual

The Bose Acoustamas 10 is a premium home theater speaker system featuring direct/reflecting speaker technology, a powered Acoustimass module for deep bass, and compatibility with various audio sources. Designed for immersive surround sound experiences, it includes satellite speakers, a bass module, and necessary cables. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operation Modes 8. Sound Optimization 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Acoustimass bass module, five satellite speakers, remote control, speaker cables, power cord.

FeatureDescription
Acoustimass ModulePowered bass unit for low-frequency effects
Satellite SpeakersFive speakers for front, center, and surround channels
Direct/Reflecting TechnologyCreates spacious, enveloping sound
Remote ControlFor volume, source selection, and sound modes
InputsLine-level inputs for receiver/amplifier connection
Power CordFor AC power connection
Speaker CablesIncluded for connecting satellites to module
Wall MountableSatellites include brackets for mounting
Auto StandbyModule enters low-power mode when not in use
LED IndicatorShows power and status on bass module

Installation

Unpack and inspect all components. Choose optimal placement for speakers.

  1. Position bass module: Place near wall or corner for enhanced bass response.
  2. Mount satellites: Install front left/right, center, and surround left/right speakers at ear level.
  3. Connect speakers: Use included cables to connect each satellite to corresponding terminals on bass module.
  4. Connect to audio source: Use RCA cables to connect module line inputs to receiver/amplifier outputs.
  5. Plug into AC power.

WARNING! Ensure proper ventilation around bass module; do not block vents. Use two people for handling heavy components.

First-Time Setup

Power on system; follow initial configuration steps.

  1. Power connection: Plug bass module into AC outlet; LED should illuminate.
  2. Source connection: Ensure audio source (receiver) is connected to module inputs.
  3. Speaker check: Verify all satellites produce sound by playing test tone from receiver.
  4. Balance adjustment: Use receiver settings to balance speaker levels.
  5. Remote setup: Insert batteries; point at bass module IR sensor.

CAUTION! Do not connect speakers to amplifier outputs directly; use only module connections.

Specifications

Controls and Settings

Primary control via remote or connected receiver. Bass Module: Power switch, LED indicator, input terminals.

Remote: POWER, VOLUME UP/DOWN, MUTE, INPUT SELECT (DVD, TV, AUX), SOUND MODE (MOVIE, MUSIC, DIRECT).

Sound Adjustment: Bass level adjustable via remote or receiver settings. No user-serviceable controls on satellites. Auto Standby: Enabled by default; module powers down after 10 minutes of no signal.

Connecting Devices

Connect to AV receiver, stereo amplifier, or compatible audio source.

  1. Turn off all devices before connecting.
  2. Use RCA cables to connect receiver subwoofer/pre-out to module line input.
  3. For stereo systems, use left/right line inputs.
  4. Ensure speaker wires are firmly connected to correct terminals (+/-).
  5. Select corresponding input on remote.

Tip: Use high-quality cables for best performance; keep cables away from power cords.

Operation Modes

Supports various audio modes for different content.

  1. Movie Mode: Enhances surround effects and dialogue clarity.
  2. Music Mode: Optimizes for stereo and multichannel music.
  3. Direct Mode: Bypasses processing for pure signal path.
  4. Volume Control: Adjust via remote or receiver.
  5. Mute: Temporarily silence audio.
  6. Input Selection: Switch between connected sources.

WARNING! Do not exceed volume levels that cause distortion; may damage speakers.

Sound Optimization

For best performance, calibrate using receiver's auto-setup or manual adjustment. Position satellites at ear level, angled toward listening area. Bass module placement affects low-frequency response; experiment with corner vs. wall placement.

Care & Cleaning

Unplug before cleaning. Use soft, dry cloth for satellites and module. For stubborn stains, dampen cloth slightly with water; do not use chemicals.

CAUTION! Do not allow moisture into speaker drivers or vents. Keep away from heat sources and direct sunlight.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Bose Corporation. All rights reserved. For support, visit www.bose.com or contact 1-800-999-2673.

Troubleshooting

SymptomPossible CauseCorrective Action
No sound from satellitesConnection/powerCheck speaker wire connections; ensure module is powered on.
Weak or no bassSettings/cablesVerify receiver subwoofer output is enabled; check RCA cable connections.
Distorted soundOverload/placementReduce volume; ensure module is not placed too close to walls.
Remote not workingBatteries/obstaclesReplace batteries; ensure clear line of sight to module IR sensor.
Hum or buzzGround loop/cablesCheck cable routing; try different power outlet; use ground loop isolator if needed.

Reset: Unplug module for 30 seconds, then reconnect.

Service: 1-800-999-2673; www.bose.com/support

Bose Acoustamas 10 Manual © - All Rights Reserved 2025